The PT-100 is a Maximum Power Point Tracker (MPPT) charge controller designed to harvest the maximum available energy from the PV array and deliver it to the batteries. The PT-100’s MPPT algorithm finds the maximum power point of the array and operates at this point while regulating the output current to 100 amps and battery voltage to fully charge the battery.
BEI Sensors PT-100 Cargador
Pbtener un precio
Para recibir una propuesta, envíe su solicitud a info@tienda-sensores.es y especifique los puestos requeridos y los detalles de la empresa.
Especificación
| Maximum PV input voltage (any condition) | 200 VDC + battery voltage or 240 VDC - whichever is lower |
| Maximum PV operating voltage | 187 VDC |
| Maximum PV array short circuit current | 100 ADC |
| Nominal battery voltage range | 12, 24, or 48 VDC |
| Battery charger output voltage range | 10 to 66 VDC |
| Continuous charger output current | 100 ADC (from -20° C to +40° C) with proportional power reduction up to 60° C ambient |
| Maximum output power | 6600 watts |
| Efficiency | 99% typical |
| Tare loss / nighttime power consumption | <4 watts (fan off, display/LEDs off) |
| Charger regulation method | Automatic three-stage (bulk, absorption, float) charge with manual equalization |
Productos relacionados
Close
BEI Sensors CSW1012 Cargador
Features
- Compact and Lightweight – The CSW provides pure sine wave power from a small footprint designed to fit in tight vehicle and marine spaces. And it is lightweight, so won’t weigh you down.
- At-a-Glance Status – The inverter’s status can be determined at a glance with the easy-to-read LED light.
- Digital Display* – The alphanumeric display shows the inverter’s battery voltage, total AC output power, along with additional operation codes. (*not available on the CSW412)
- USB Port – Power and charge your USB-enabled device with the available USB port.
- GFCI AC Outlet – Plug in two pieces of equipment directly to the CSW and know that the GFCI outlet will quickly stop the flow of electricity should a ground fault occur. The outlet also comes with an LED indicator and test/reset capability.
- Automatic Transfer Switch Option – The CSW2012-X automatically switches between shore power and inverter/battery power.
Close
BEI Sensors Cargador
Features
- GFCI Outlet – Provides 120 VAC output as well as receptacle protection.
- Unit Protection – Provides automatic electronic short circuit/ overload protection, automatic over-temperature shutdown, and an AC output circuit breaker.
- Status LED – Provides inverter operation mode and troubleshooting information at a glance.
- Low Battery Protection – Automatically shuts down at 10.5 VDC with in-rush delay. The end user may also select an optional setting of 11.7 VDC.
- Battery Surge Protection – The 12LP10 has an input DC voltage range of 10.5 - 16 volts. The inverter can tolerate up to 24 VDC for five minutes, then will shut down to preserve the system.
- Auto Sleep Mode – Auto sleep mode helps preserve battery life over long periods of no load operation.
Model Numbers
- 12LP10
- 12LP10H
- 12LP10R
Close
BEI Sensors ME-AGS-N Cargador
Features
- Automatically start your generator – The AGS is designed to automatically start your generator based on low battery condition or the inside room temperature.
- Adjust the AGS to meet your needs – With the ME-AGS-N you can set multiple parameters for starting and stopping the generator. Using the ME-RC, the ME-AGS-N has basic adjustments starting on battery voltage or temperature. When using the ME-ARC, the ME-AGS-N has advanced start and stop features, including battery voltage, time of day, AC amps, exercise time, and SOC.**
- Two models are available – The stand alone version of the AGS (ME-AGS-S) works well for installation and operation without an inverter. The network version of the AGS (ME-AGS-N) allows operation of the AGS via the ME-RC or ME-ARC remote panel.
Close
BEI Sensors MS2812 Cargador
Features
- Pure Sine Wave – Power your TVs, computers, and other sensitive electronics without worry. The MS Series provides clean, reliable inverter power with low total harmonic distortion (THD) of less than 5%.
- Accessible Design – The extra large AC access cover with terminal screw block and 360° DC connection terminals with covers make this inverter accessible.
- Choices – The MS Series comes in 12, 24, and 48 volt configurations, allowing you to choose the model that is right for you.
- Versatile Mounting – Mount the MS Inverter/Charger on a shelf, bulkhead, or even upside down.
- Lightweight – The lightweight aluminum base and cover also provides noise reduction and corrosion resistance.
- Multiple Ports – The MS Series provides multiple ports, including an RS485 communication port for network expansion, and a remote port.
- Convenient Switches – The MS Series comes with an on/off inverter-mounted switch with an easy-to-read LED indicator.
- Expanded Transfer Relay – 60 Amp transfer service is available on all models except MS2000, which is 30 Amp only.
Close
BEI Sensors CC-30 Cargador
Features
- Shunt topology with MOSFETs
- Accurate state of charge (SOC) determination
- Automatic detection of voltage
- PWM control
- Multistage charging technology
- Load disconnection depending on SOC
- Automatic load reconnection
- Temperature compensation
- Option to use negative earthing of one or positive earthing of several terminals
- Integrated data logger (energy meter)
- Evening, night light and daylight functions
- Integrated self test
- Monthly equalization charge
- USB charge socket for smartphones and tablets (CC-40 only
Model Numbers
- CC-30
- CC-40
Close
BEI Sensors ME-SBC Cargador
Features
- Voltage auto-detect feature recognizing 12 or 24 VDC.
- Transfers up to 25 amps.
- Solenoid drive for requirements greater than 25 amps.
- Over-temperature and over-current shutdown.
- Adjustable voltage settings with a wide range allows for charging flexibility.
- Bi-directional charging.
- Reverse polarity protection.
- Sense lead for long-run applications.
The Front Panel Includes
- LED indicators showing status and operation.
- Three adjustable voltage dials to set the “Connect Voltage”, “Low V Disconnect”, and “High V Disconnect.”
- An oversized power terminal block allowing for easy wire connections even if the wires are large.
- An accessories terminal block to add a solenoid or a separate voltage sense line.
- A reset switch.
Options
- The ME-SBC also works as a stand-alone unit.
Close
BEI Sensors MS4048 Cargador
Features
- Pure Sine Wave – Power your TVs, computers, and other sensitive electronics without worry. The MS Series provides clean, reliable inverter power with low total harmonic distortion (THD) of less than 5%.
- Accessible Design – The extra large AC access cover with terminal screw block and 360° DC connection terminals with covers make this inverter accessible.
- Choices – The MS Series comes in 12, 24, and 48 volt configurations, allowing you to choose the model that is right for you.
- Versatile Mounting – Mount the MS Inverter/Charger on a shelf, bulkhead, or even upside down.
- Lightweight – The lightweight aluminum base and cover also provides noise reduction and corrosion resistance.
- Multiple Ports – The MS Series provides multiple ports, including an RS485 communication port for network expansion, and a remote port.
- Convenient Switches – The MS Series comes with an on/off inverter-mounted switch with an easy-to-read LED indicator.
- Expanded Transfer Relay – 60 Amp transfer service is available on all models except MS2000, which is 30 Amp only.
Close
BEI Sensors ME-BMK-NS Cargador
Features
Available Readings from the ME-BMK / ME-BMK-NS:- State of Charge (SOC) 0 - 100%
- DC volts
- DC amps
- Amp hours in/out
- Resettable amp hours out
- Total amp hours out
- Minimum volts DC
- Maximum volts DC
- Temperature compensated
- Auto detects input voltage